puremor FILM
Silicone projection screen film concept in a passenger cabin

NEW MATERIAL · CROSSLINKED SILICONE

A new generation ofsilicone projection
screen film.

A crosslinked-silicone viewing surface for front projection. PVC-free, flame-retardant, wipe-clean and resistant to yellowing — already qualified for automotive interiors.

  • NOT PVC
  • NOT Melamine
  • NOT PP
  • NOT PETG
  • Silicone surface
2HPencil scratch test
2,000Taber abrasion cycles
FRFlame-retardant · GB 8410 burn-rate passed
OEMAutomotive-interior qualified

Front projection · Flame-retardant · No adhesive · Seamless one-piece sheets

A NEW SURFACE MATERIAL

Silicone on the surface.
Not another PVC projector screen.

Most projector screen materials are PVC sheet, coated fabric or a plastic film with a printed coating. Puremorfilm is different: the viewing face is a crosslinked silicone layer, formed and bonded to a polymer support in a continuous roll-to-roll process — the same silicone technology developed for automotive interiors.

Buyer problem

Handling marks on the screen

Material approach

A low-surface-energy silicone face helps everyday marks release during cleaning.

Screen-level check

Check cleaning on the projected image, as well as the bare surface.

Buyer problem

Layer stress during assembly

Material approach

A continuous crosslinked silicone interface distributes load between layers instead of relying on simple physical contact.

Screen-level check

Test the intended bending or winding geometry on the finished construction.

Buyer problem

Colour drift after light exposure

Material approach

Weatherability and yellowing resistance are functions of the silicone surface; UV-stabilised formulations are part of the material platform.

Screen-level check

Evaluate colour and image appearance after the project’s ageing cycle.

Buyer problem

Material selection for an enclosed cabin

Material approach

The silicone film uses a No DOP formulation. Backing and adhesive are considered as part of the whole material stack.

Screen-level check

Use the complete construction for VOC, odour and fogging qualification.

Material mechanisms and results are documented in the technical white paper.

See the Test Data →

MATERIAL COMPARISON

How Silicone Film Compares with Other Projector Screen Materials

Row by row: what the viewing face is made of, how it cleans, how it ages and how it mounts. The other columns describe each material category in general, so check the grade you are offered.

Projector screen materials compared by category. Compare actual samples on your own projector.
Puremorfilm silicone filmPVC screen sheetCoated fabricPP / PETG film
Viewing surfaceCrosslinked siliconePVC with top coatCoated woven textilePlastic film, coated or printed
Seams across the imageSeamless one-piece sheets, cut to your screen sizeDepends on roll width and screen sizeDepends on roll width and screen sizeDepends on roll width and screen size
MountingPlain back, no adhesive: frame, tension or your own laminationDepends on the screen systemUsually tensioned in a frameDepends on the screen system
DOPNo DOP formulationCheck DOP content for the selected formulationDepends on coatingConfirm the selected grade
CleaningLow-surface-energy face; marks wipe offDepends on top coatWeave texture holds dust; hard to wipeDepends on coating
YellowingSilicone resists yellowingCan yellow with heat and UVDepends on coatingDepends on grade
Flame behaviourFlame-retardant; passed GB 8410 automotive burn-rate testDepends on grade and additivesDepends on fire treatmentDepends on grade
Automotive interiorOEM qualification passedDepends on gradeDepends on gradeDepends on grade

Put a sample next to your current screen material and project the same image on both.

Request a Comparison Sample →
Front projection screen film concept in a home media room
Concept visual

HOME PROJECTION SCREENS

A seamless front projection screen that wipes clean.

For screen manufacturers and home-cinema integrators. One-piece silicone film with a No DOP formulation and no seams across the image.

  • Seamless one-piece sheetsNo joins across the picture area.
  • Wipe-clean silicone faceFingerprints and fitting marks release with a soft cloth.
  • No adhesive, your mountingPlain-back film for frames, tensioned or laminated builds.
  • Flame-retardant by materialA safer surface for home cinemas, meeting rooms and public venues.

Start with your screen size and the projector you plan to use.

Discuss a Home Screen ↓

IN-VEHICLE PROJECTION

Already in production in a vehicle projection screen.

Puremorfilm silicone film is used in projection screens built for a production electric-vehicle programme, and has passed the OEM's interior surface-material qualification.

  • Qualified for the cabinHeat ageing, odour, fogging, flammability and dimensional stability all passed. See the data below.
  • Flexible, stable layersContinuous crosslinked silicone layers handle bending and mounting stress.
  • Built for integrationPlain-back film, cut to your screen geometry.

A non-confidential drawing is enough to open the technical discussion.

Discuss a Vehicle Display ↓
Projection surface concept inside a passenger cabin
Concept visual

WHAT YOU ARE SOURCING

A silicone face on a polymer support.

The silicone layers are the viewing surface. The polymer film underneath only provides support — it is never the surface your audience sees.

Silicone functional surfaceSurface care, weatherability and appearance.
Silicone structure + bonding systemFlexibility and continuous interlayer crosslinking.
Polymer-film backingMechanical support and the screen assembly interface.
Material-platform diagram · functional grouping, not a scaled projection-grade drawing.

Supplied ready to mount

  • Front projection grade
  • No adhesive — plain back for frame, tension or your own lamination
  • Seamless one-piece sheets, cut to your screen size
  • Surface finish, gloss and support thickness can be tuned for OEM projects

Choose the usable width and mounting format for your screen.

See Front Projection Specs →

FRONT PROJECTION

Front projection screen film specifications.

Designed for front projection: projector and audience on the same side.

Front projection layout

Front projection: projector and viewer on the same side ProjectorFilmViewer

The projector and audience are on the same side of the screen.

Front projection film specifications
ParameterPuremorfilm projection grade
Projection typeFront projection
AdhesiveNone (plain back)
Supply formatSeamless one-piece sheets
Usable width1,240 / 1,260 / 1,400 mm
SurfaceCrosslinked silicone
Flame behaviourFlame-retardant; burn rate ≤100 mm/min (GB 8410)

Get the construction and test details for your front projection screen film.

Request the Full TDS ↓

Material evidence

Numbers you can trace to a test.

The technical white paper reports scratch, abrasion and heat-stability measurements for the silicone composite material platform.

2HPencil test · no obvious scratches
2,000Taber abrasion cycles · slight mattification
100°C600-minute dimensional-stability test
Material-test summaries reported in the technical white paper V1.0 (October 2026)
Test / reportMethod & conditionsReported result
Scratch · SZIN2608002405PL02_EN2H pencil; 500 gf; 45°; three 20 mm strokes.No obvious scratches.
Abrasion · SZIN2608002405PL04_ENASTM D4060-25; CS-10; 1,000 g per wheel; 60 rpm; 2,000 cycles.Slight mattification; no concentrated scratches, substrate exposure or coating peeling.
Heat stability · SZIN2608002405PL01_EN100°C × 600 minutes; measurement after 14-hour recovery.Length change 0.06%; width change 0.10%.

Source: SGS-CSTC test reports, August 2026. Report numbers listed above; full reports available on request.

OEM automotive-interior qualification: passed

Puremorfilm silicone film has passed an OEM interior surface-material specification. Acceptance requirements met:

OEM automotive-interior qualification requirements met
PropertyRequirement metTest conditions / method
Heat ageingGrade ≥4.90°C forced-air oven × 168 h; grey-scale colour assessment.
OdourGrade ≤3.Customer automotive-material odour method B.
Fogging≤2.5 mg.Gravimetric fogging method for automotive interior materials.
FlammabilityBurn rate ≤100 mm/min.GB 8410 method stated in the customer specification.
Dimensional changeWithin ±2%.100 ±2°C × 4 h; longitudinal and transverse measurements.
Stain resistance & cleaningGrade ≥4 after 1 h; ≥3–4 after 24 h.Soil, sewing-machine oil and coffee; cleaning and GB 250 grey-scale assessment.
Additional colour, coating, humidity and substance requirements
Additional automotive surface-material requirements
PropertyAcceptance requirementTest conditions / method
Initial colour matchΔE ≤0.6 versus the approved reference.Uniform coating and colour; no wrinkles, blisters or cracking.
Light colour fastnessGrade 3–4.Xenon exposure: 1,240 / 488 / 225 / 112 kJ/m², selected by installation location.
Coating adhesion≥4 N/10 mm.GB/T 4689.20 method stated in the customer specification.
Humidity resistanceNo mould or unpleasant odour.38 ±2°C, 95 ±5% RH, 7 days.
PAHsIndividual listed PAHs <0.5 mg/kg; naphthalene <2 mg/kg; sum of 18 PAHs <10 mg/kg.Scope and extraction method follow the customer surface-material specification.

Review the reports and OEM qualification requirements for your project.

Request the Test Reports ↓

Dimensions & technical specification

Start with a concrete material range.

The published material platform provides a starting point for width, roll format and backing selection. The offered projection grade defines the final combination.

Platform effective widths

1,240 / 1,260 / 1,400 mm

Available combinations depend on the selected construction.

Supply format

Seamless one-piece sheets

Cut to your screen size. Rolls for production volumes.

Polymer backing range

80–1,000 μm

Backing thickness only; this is not total projection-film thickness.

Compare cost per usable screen area.

Include film price, usable-width yield, edge allowance, support, bonding or tensioning, assembly labour and freight. A cheaper roll can become a more expensive screen when waste and rework are included.

Share your screen size and quantity for a quote.

Get a Quote for Your Screen Size ↓

Sample to order

Four decisions from first sample to supply.

One clear approval sequence covers the optical trial, material requirements and production order.

  1. Define the screen

    Send the application, image size, light path and material requirements.

  2. Approve the sample

    Standard samples ship within 3 days. Test them on your own projector.

  3. Approve the construction

    Run the assembly and application tests. Lock the grade, TDS and reference sample.

  4. Place the order

    Approve quantity, price, inspection, packing and the delivery schedule.

Standard samples ship within 3 days. Production lead time is quoted with your order quantity.

Request a sample, a trial-batch quote or the documents needed for approval.

Start My Film Sample Request

Before you enquire

Projection screen film FAQs.

Is this a PVC projector screen material?

No. Puremorfilm is a new silicone surface material. The viewing face is crosslinked silicone — not PVC, melamine, PP or PETG — and it uses a No DOP formulation.

Is it for front projection?

Front projection: the projector and audience are on the same side of the screen.

Is the film self-adhesive?

No. It is supplied with a plain back, so you can frame it, tension it or laminate it with your own process.

What sizes can I order?

Seamless one-piece sheets cut to your screen size, with usable widths of 1,240, 1,260 or 1,400 mm. Rolls are available for production volumes.

Is it qualified for automotive interiors?

Yes. Puremorfilm silicone film has passed an OEM interior surface-material specification, including heat ageing, odour, fogging, flammability and dimensional stability. The requirements are listed in the test data section.

Is the film flame-retardant?

Yes. The silicone material is flame-retardant and has passed the GB 8410 automotive-interior burn-rate requirement (≤100 mm/min). If your project needs a specific fire rating, such as NFPA 701, DIN 4102 B1 or EN 13501-1, tell us the standard and we'll confirm the matching test.

Will it work with my projector?

Send your projector model, throw distance and screen size. We'll send a sample so you can test it on your own setup before ordering.

How fast are samples, and what about MOQ and price?

Standard samples ship within 3 days. Price and minimum order are quoted against your screen size and quantity.

What do I need to start?

Just your email. Screen size, projector details and quantity can follow.

Your email is enough to begin. Technical details can follow with the sample brief.

Go to the Film Enquiry

GET A SAMPLE

Test it on your own projector.

Standard samples ship within 3 days. Tell us your screen size and projector — or just leave your email.

Tell us whether you are developing a home screen or a passenger-cabin display. Add the screen size, projector layout or a material requirement when you have it.

Only email is required.
Optional: application, dimensions, quantity and a non-confidential file.

Request projection film samples

Only email is required. Add the project details you already know.

Add company, specification, quantity or files

Up to 3 files, 10 MB each. You can also submit without an attachment.

    Share your application and receive the samples, documents or quote you requested.

    We'll use your email to reply to this request.