puremor FILM
Furniture decorative film on matte kitchen cabinet doors and island fronts

FURNITURE DECORATIVE FILM

Furniture film,
reinvented in silicone.

Puremorfilm is a Chinese manufacturer of silicone decorative film and silicone laminated panels, with a silicone functional surface on a PET support film. We supply rolls without a self-adhesive backing for PUR flat lamination, or laminated panels quoted per project, for furniture fronts, cabinet doors, wall panels and other vertical or low-wear surfaces; neither supply form is suitable for floors, countertops or stovetops.

PVCMelaminePPSilicone

2H scratch-tested · 0 added formaldehyde · Cigarette-burn resistant

MATERIAL COMPARISON

Furniture Decorative Film vs PVC Thermofoil, Melamine, HPL and PP Film

A new generation of PVC-free furniture film brings silicone’s leather-like touch and easy-clean surface to furniture design. See how it compares with PVC thermofoil, melamine and HPL in touch, everyday care and surface performance. For a closer look at material choices, explore kitchen cabinet materials or compare wood veneer and laminate.

Compare furniture surface materials, property by property.
What you compare PuremorfilmSilicone film PVC thermofoilMelamine faced boardHPLPrinted PP film
Touch and feelSoft, skin-like matt touchFinish-dependent; soft-touch grades existHard resin-faced surfaceHard, dense laminateSmooth, thin plastic feel
Everyday cleaning24-hour stains wipe cleanEasy-clean grades availableEasy-clean sealed surfaceStrong everyday stain resistanceDepends on topcoat
Scratch resistance2H: no obvious scratchesDepends on protective topcoatHard-wearing; check surface classHard-wearing; check EN 438 gradeTopcoat-dependent; soft films mark
Surface wear2,000 cycles; slight mattificationWear-layer dependentGrade-dependent wear classAbrasion-rated grades availableWear resistance: topcoat-dependent
Heat stability0.06%/0.10% change, 100°C/600-min testHeat-sensitive film and adhesive systemGrade and exposure-time dependentHeat-resistant grades availableThermoplastic; check heat rating
Cigarette contactCigarette-burn-resistant filmRequest grade-specific contact resultCheck the surface ratingResistant grades availableRequest grade-specific contact result
Ageing over yearsNo DOP; resists embrittlementFormulation-dependent plasticizer migrationStable; grade-dependent appearanceStable resin laminateStable; topcoat may wear
Surface materialPVC-free; no added formaldehydePVC-based; formulation-dependent additivesResin paper; low-emission grades existResin laminate; low-emission grades existPVC-free polymer; check coatings
Profiles and edgesFlat lamination with PUR adhesive3D thermoforming of suitable gradesFlat panels; edge banding neededFlat bonding / grade-specific postformingFlat lamination and wrapping
Compare with:

Silicone vs PVC thermofoil

Silicone film alongside the selected furniture surface.
PropertySilicone filmPVC thermofoil
Touch and feelSoft, skin-like matt touchFinish-dependent; soft-touch grades exist
Everyday cleaning24-hour stains wipe cleanEasy-clean grades available
Scratch resistance2H: no obvious scratchesDepends on protective topcoat
Surface wear2,000 cycles; slight mattificationWear-layer dependent
Heat stability0.06%/0.10% change, 100°C/600-min testHeat-sensitive film and adhesive system
Cigarette contactCigarette-burn-resistant filmRequest grade-specific contact result
Ageing over yearsNo DOP; resists embrittlementFormulation-dependent plasticizer migration
Surface materialPVC-free; no added formaldehydePVC-based; formulation-dependent additives
Profiles and edgesFlat lamination with PUR adhesive3D thermoforming of suitable grades

Silicone figures refer to the recorded film specimens. Other columns describe typical material categories; grades and test methods vary. View silicone test conditions. Film, adhesive and core-board performance are assessed separately.

Compare a physical sample against your current finish.

Request a Comparison Sample

See How the Surface Addresses Your Furniture Problems

Start with cleaning and cigarette contact, then evaluate the matching film on your own furniture construction.

Furniture film surface with cigarette scorch and ashtrayWatch video0:32

Check cigarette-contact performance

Request the result, contact time and specimen details for your chosen grade. Cigarette-burn resistance and flame retardancy are evaluated separately.

Request Burn Test Details →

Evaluate the surface on samples before specifying it.

Request Samples for Evaluation

Furniture Film Manufacturing & Quality Control

Review production capability, then agree the quality checks for your order. Watch the factory video

  • 10+years in decorative surface materials
  • 6lines for printing, coating and lamination
  • 1M+ m²monthly film capacity
  • 100+patterns ready to sample

From coating to finished rolls

Explore the coating, curing and roll-finishing stages. See our operating production lines on a live video factory tour.

Silicone film coating line with raw-material tanks in the Puremorfilm factoryFactory video1:15
Coating line
Operator at a film unwinding and processing machine on the Puremorfilm production floor
Film processing
Workers inspecting white base film on a roll inspection table
Roll inspection

Quality checkpoints from incoming materials to dispatch

Agree the inspection items, tolerances and records with the approved sample before production.

  1. 01

    Incoming materials

    Material specification, batch identity and surface condition.

  2. 02

    During production

    Thickness, coating uniformity, colour, texture and visible defects.

  3. 03

    Finished rolls

    Width, length, appearance and grade-specific acceptance checks.

  4. 04

    Before dispatch

    Model, batch labels, quantity and protective packing against the order.

Acceptance, nonconforming material & traceability

Confirm the approved reference sample and inspection frequency. Agree how nonconforming material is identified, held and rechecked, and which production and inspection records accompany the supplied batch. Request the applicable QC checklist for your order.

Review the production lines and discuss your inspection requirements.

Book a Video Factory Tour Request QC Details

Choose a Finish for the Furniture You Make

Select an application to see the checks that matter before sampling and production.

Application limits: no floors, countertops or stovetops

Keep the film off working surfaces

Do not specify the current film for countertops, desktops used as worktops or stovetops. Use it for vertical or low-wear furniture faces instead.

What matters most
Cleaning, cigarette-burn resistance, everyday wear
What we confirm next
Film sample for stain and burn checks, plus your board type
Ask About Tabletops & Desks

Need a reference for a similar application? Ask about available project references.

Discuss a Similar Project

Judge the Look and the Touch with Real Samples

Explore wood grain, solid colours and leather textures. Request physical samples to compare colour, texture and touch. A panel sample also shows the finish after bonding.

Wood grain

Choose a finish family and compare the actual material in your hands.

Request Colour Samples

Film Rolls or Laminated Panels: Confirm Your Specification

Choose what fits your production setup. Supply combinations and tolerances are confirmed for the selected model.

Silicone decorative film roll

Film rolls for your lamination line

Effective width
1240 / 1260 / 1400 mm, by model
Roll length
50 / 100 / 250 / 500 m, by model
Thickness & backing
Total thickness, tolerance and backing confirmed by grade
Back adhesive
Standard supply without back adhesive
Quote Film Rolls
Silicone decorative film laminated panel structure

Laminated panels for further fabrication

Core & thickness
Specify the board type, grade and thickness
Size
Confirm the furniture panel size and cutting allowance
Film face
Selected finish, one or two faces as agreed
Acceptance
Appearance, bonding and project requirements by construction
Quote Laminated Panels
Backing, gloss & documented panel size

Product literature lists PET support film and development options including PC or TPU; confirm the backing for the selected grade. Gloss is approved on a physical sample. The documented 1220 × 2440 mm size is a wall-panel specification; furniture-panel size is confirmed separately.

Not sure which supply form to choose? Describe your equipment and end product.

Help Me Choose a Supply Form

Film Performance: Recorded Results & Test Conditions

Review the highlights, then expand the records you need. Results apply to the stated film specimen or formulation; finished-panel requirements are confirmed by construction.

Pencil scratch

No obvious scratches

2H pencil · 500 gf · 45° · three strokes ≥20 mm. White paper summary of SGS PL02.

Taber abrasion

2,000 cycles

Slight mattification only; no concentrated scratches, exposed backing or coating peeling. CS-10 · 1,000 g per wheel · 60 rpm. SGS PL04 summary.

Thermal dimensional change

0.06% / 0.10%

Length / width after 100°C for 600 minutes and 14-hour room-temperature recovery. SGS PL01 summary.

Source: technical white paper V1.0 (October 2026), including SGS report summaries, laboratory records and patent worked examples. Request the original matching report for the supplied model.

SGS report summaries — four film tests
Test itemRecorded resultTest conditionsSource & scope
Pencil scratchNo obvious scratches2H pencil; 500 gf load; 45° angle; three strokes, each ≥20 mm.SZIN2608002405PL02_EN
26 Aug 2026. Tested film specimen; resistance under these tool and load conditions.
Taber abrasion2,000 cycles: slight mattification only; no concentrated scratches, substrate exposure or coating peeling.ASTM D4060-25; CS-10 wheels; 1,000 g per wheel; 60 rpm.SZIN2608002405PL04_EN
27 Aug 2026. Surface-wear evidence for the tested film; assess against the intended wall or furniture use.
Thermal dimensional stabilityLength change 0.06%; width change 0.10%.100°C for 600 minutes, followed by 14 hours at room temperature. Lab environment: 23±2°C, 50±5% RH.SZIN2608002405PL01_EN
26 Aug 2026. Supports dimensional and processing evaluation of the tested film.
Tensile breaking force & elongationA1: 216.4 N / 51%
A2: 126.3 N / 67%
Specimen thickness: A1 0.473 mm; A2 0.605 mm.
JIS K 6732:1996+AMD.1:2006 and client requirements; 200 mm/min; 40 mm gauge length; 23±2°C, 50±5% RH.SZIN2608002405PL03_EN
27 Aug 2026. N is breaking force. Specimens 1 and 2 broke outside the gauge marks; those results are for reference only.
Laboratory records — stains & cleaning
Test itemRecorded resultTest conditionsSource & scope
Food, drink & cosmeticsNo visible change after wiping: coffee, red wine, ice cream, soy sauce, Worcestershire sauce and lipstick.Contaminants applied to the film surface; held at 25°C for 24 hours, then wiped.Laboratory data, white paper §6.2. Results apply to the stated exposure and wiping method; match cleaners to the supplied grade.
Pen & marker marksNo visible change or slight staining: ballpoint pen, water-based marker and oil-based marker.Same recorded method: 25°C for 24 hours, followed by wiping.Laboratory data, white paper §6.2. The recorded result varies; confirm the contaminant-specific result for the chosen film.
Patent worked examples — interlayer stability & antibacterial grade
Test itemRecorded resultTest conditionsSource & scope
Internal film interlayer peelBOPET system: ≥3 N/15 mm
TPU system: ≥3.5 N/15 mm.
180° peel; BOPET backing 125 μm and TPU backing 200 μm.Patent worked examples 1 and 2, white paper §5.4. Internal film interface only; does not establish film-to-board adhesive strength.
Damp-heat ageingNo delamination or blistering.85°C / 85% RH for 500 hours.Patent worked-example data, white paper §5.4. Confirm the corresponding construction for supply.
Thermal cyclingNo delamination or blistering.−40°C to 85°C; 100 cycles.Patent worked-example data, white paper §5.4. Applies to the evaluated example construction.
Boiling-water exposureNo delamination or blistering.Boiling water for 12 hours.Patent worked-example data, white paper §5.4. Confirm film grade and construction.
Antibacterial reduction≥99% against Escherichia coli and Staphylococcus aureus.Recorded for an antibacterial worked-example formulation. Confirm formulation grade and corresponding test conditions.Patent worked-example data, white paper §9. Antibacterial performance is grade-specific; request evidence for the supplied model.
Surface wettabilityWater contact angle approximately 108° in the worked example; stated range 100°–115°.Worked-example surface measurement; full measurement conditions to be matched to the grade.Patent worked-example data, white paper §6.1. A wettability measure for the evaluated surface.
Additional laboratory records — weathering & exposure
Test itemRecorded resultTest conditionsSource & scope
Accelerated ageingNo visible change after 2,000 hours.White paper records JIS B7753 light and water exposure testing.Laboratory data, white paper §7.2. Confirm the original exposure program and film grade for a weathering specification.
Yellowing resistanceGrade ≥4.QUV-A testing, as recorded; duration and grading details to be confirmed with the matching test record.Laboratory data, white paper §7.2. Compare only with a matching procedure and grading scale.
Hydrolysis exposureRecorded duration ≥10 weeks.85°C / 85% RH.Laboratory data, white paper §7.2. Request the appearance/strength acceptance criteria for the specified grade.
Salt-spray exposureRecorded duration ≥1,000 hours.ASTM B117, as recorded in the white paper.Laboratory data, white paper §7.2. Project acceptance criteria and the post-exposure result are confirmed separately.
Water stainingClass 5.ISO 105-E01 / ASTM D1735-2021, as recorded.Laboratory data, white paper §7.2. Confirm the grading procedure and specimen.
Perspiration stainingClass 5.ISO 11641:2012 / ISO 105-E04, as recorded.Laboratory data, white paper §7.2. Confirm the intended contact conditions and film grade.
Material safety, cigarette contact & fire performance

The film layer is described as having no added formaldehyde and a No DOP formulation. Request the matching material-safety document. For laminated panels, assess the adhesive and core separately.

Cigarette-contact results need the film grade, contact time and method. Flame-retardant performance needs the applicable standard and construction. One result does not establish the other.

Develop a Finish for Your Collection

Share a reference sample or design brief for a custom colour, pattern or texture. Feasibility and supply terms are confirmed before proofing.

Colour & pattern

Reference colour, wood grain or a design file, with the intended furniture application.

Texture & touch

Describe the grain, gloss and hand feel you want to compare on a physical proof.

Specification & identification

Discuss the required width, thickness, quantity and any packaging or labelling needs.

Design brief → Feasibility & terms → Physical proof → Approved production reference

Have a finish reference? Add it to your inquiry.

Discuss a Custom Finish

Confirm the Film, Adhesive, Board & Process Together

Share your substrate, adhesive and equipment. Trial the proposed construction and edge treatment before a volume order; compatibility is confirmed for the selected film grade.

What goes into one laminated surface

  • Silicone surface layerTouch, cleaning and burn performance
  • Decorative filmPrinted colour and texture on the base film
  • AdhesiveChosen to suit your board and equipment
  • Core boardMDF, particleboard, plywood or other cores
Bond strength depends on all four layers and on the lamination process, so we evaluate them together.

What to share with us

  • SubstrateBoard type, thickness and surface condition
  • Adhesive systemThe glue you use today or plan to use
  • Equipment and processYour flat lamination line, with temperature, pressure and speed
  • Where it is usedDoor front, edge or side panel; exclude worktops
  • Acceptance criteriaThe bond, appearance and tests your buyer will check
Three checks before changing your face material
  • Confirm whether your adhesive and line settings suit the selected film.
  • Evaluate the finished bond and edges; internal film peel data is a different measurement.
  • Agree appearance and performance acceptance on the laminated sample.

Send your substrate and process details — we will check the fit before you order in volume.

Submit My Substrate & Process

Get a Quote for Your Actual Purchase

Evaluate the cost of an accepted finished surface, including your processing and delivery requirements.

Material

Grade, finish, thickness and supply form.

Processing

Adhesive, labour, line settings and yield.

Packing

Roll or panel protection and order size.

Delivery

Destination, freight method and schedule.

For a useful quote: send the application, supply form, specification, estimated quantity and destination. Include your preferred finish if known.
How MOQ and purchase terms are confirmed

Standard film rolls start at 500 m; laminated panels are 1220 × 2440 mm and start at 200 sheets. Unit price depends on the selected grade, specification, finish and quantity. A custom finish may require separate proofing and a different production quantity. Request a quote that states sample costs, freight, MOQ, lead time and packing.

Share what you know now; missing details can be confirmed during evaluation.

Get a Project Quote

From Approved Sample to Checked Shipment

Confirm the material and acceptance requirements first, then agree the production and delivery plan.

  1. 01

    Select & approve samples

    Choose the finish and film or panel sample for your application.

  2. 02

    Trial & confirm the order

    Agree the construction, specification, acceptance criteria, quantity and terms.

  3. 03

    Produce & inspect

    Confirm the production checks, batch identification and inspection records.

  4. 04

    Pack & dispatch

    Agree protective packing, outgoing checks, documents and freight arrangements.

Sample dispatch, proofing & production planning

Planning guide: sample dispatch 3–5 working days; standard bulk production 15–25 days after deposit; custom patterns may add 7–10 days for proofing and approval. Confirm the actual schedule with the quote against the model, quantity and requirements. Freight transit is planned separately.

Begin with a sample set and the checks you want to run.

Start Sample Evaluation

Before You Sample & Order

A few final checks for furniture makers and project buyers.

Is this furniture film PVC-free?

Yes. The surface is crosslinked silicone on a PET support film — not PVC, melamine paper or a printed PP film. It uses a No DOP formulation.

Is it formaldehyde-free?

Yes. The film layer has no added formaldehyde. For laminated panels, the adhesive and core board are documented separately so your project file covers every layer.

How is this film applied to furniture surfaces?

Standard film rolls are supplied without back adhesive. Confirm the adhesive, board and lamination method for the selected grade, then trial the construction on your line. Laminated panels are an alternative when you need the film already bonded to a board.

How do I verify cigarette-burn resistance?

Each burn result is tied to a named film model and the stated test conditions, including contact time and placement. Ask for the record of the model you plan to use and we will share the result with its conditions.

Does the film fire result cover a laminated panel?

Not automatically. Film results describe the film. A laminated panel's fire performance depends on the film, adhesive and core board together, so it is evaluated by construction for your project.

Which sample type should I request?

Colour swatches help you choose the look. Film samples let you test cleaning and run lamination trials on your own line. Panel samples show how the finished door or furniture panel looks and feels once the film is bonded.

How are MOQ, pricing and lead time confirmed?

Standard film rolls start at 500 m; laminated panels are 1220 × 2440 mm and start at 200 sheets. Unit price, lead time and packing are confirmed for the selected model, supply form, specification and quantity.

Have a question not covered here? Our technical team will answer it directly.

Ask a Technical Question

Request Furniture Film Samples or a Project Quote

Choose samples, a quote, test documents or a processing discussion. Share your application and any selected finish; only your email is required.

Decorative film colour swatches and laminated panel samples for selection
  • Colour swatches, film samples or panel samples
  • Test summaries for the model you choose
  • Processing advice for your substrate and line

Request samples or advice

Choose what you need. Only your email is required.

Enter a valid email so we can reply.

What would you like?
Add company, quantity, specification or files

    We reply by email with the samples, documents or quote you asked for.

    We only use your email to reply to this request.

    Puremorfilm video